Fairey capstan winch base plate screw. Part no: FWL-151-A4. PLEASE NOTE: These are the M6 metric version fitted to later winches. Earlier winches used a 1/4"BSF thread. Please check before ordering...
Fairey Capstan Winch Bollard Cap to Bollard Bolt. Part no: FWL-164-A4. Finish: Sherardized. Please note: This is the later UNC threaded bolt, early MAP winches were BSF so please check before ordering...
Fairey capstan winch crankshaft drive dog (imperial) Part no: FWL-136-A3. For 2.25l 3 main bearing engines and 2.6 6 cylinder engines. Highly accurate part with the correct locating key machined into the drive dog. Manufactured from EN24T steel...
Fairey capstan winch crankshaft drive dog (METRIC) Part no: FWL-6266-A3. For later 2.25l 5 main bearing engines with the M20 metric threaded crank. Also suitable for the 2.5 engines upto 200tdi.Highly accurate part with the correct locating key machined into the drive dog. Manu..
Fairey capstan winch crankshaft drive dog bolt. IMPERIAL 3/4" thread for 3mb 2.25l engines and 2.6 6 Cylinder engines. Part no: FWL-134-A4 Manufactured from EN24T and phosphated for corrosion protection...
Fairey capstan winch crankshaft drive dog bolt. METRIC M20 thread for 5mb 2.25l engines and later 2.5l enginesPart no: FWL-6267-A4 Manufactured from EN24T and phosphated for corrosion protection...
Fairey Capstan Winch Driveshaft for Land Rover Series 2, 2a 3Corresponds to part no: FWL-444-A3Manufactured from EN8 steel and has bearings at the end of shaft like the original...
Fairey capstan winch driveshaft UJ. Part no: FWL 186-A3 Supersedes: FWL-124, Please note: This is the late type UJ with the additional dog point grub screw for securing the UJ to the wormshaft when the shear pin fails. This replaces the earlier roll-pin, circlip & earl..
Fairey capstan winch fairlead assembly. Part no: FWL-1030-A3, FWL-1034-A3. Highly accurate reproduction fairlead assembly. Brackets are powder-coated and the roller is Zinc plated. ..
Fairey capstan winch operating lever spring. Part no: FWL-143-A4Manufactured from spring stainless steel unlike the originals for better corrosion protection...
Fairey Capstan Winch steel driveshaft pin. Part no: FWL-172-A4 To be used when hand cranking the engine, must be replaced with a brass shear pin before commencing winching operations.Fits both 3000lb & 4000lb variants...
Fairey capstan winch UJ locating grub screw (dog point) Part no: FWL-5283-A4. PLEASE NOTE: This grub screw is used on the late style UJ where a grub screw locates in a groove on the end of the wormshaft (apposed to a 1/8" spring pin (early Fairey models) and a circlip (MAP versions) ..
Fairey Capstan Winch worm shaft. Part no: FWL-187-A3. This is the late spec wormshaft for UJ's secured by grub screws as opposed to earlier circlip and spring pin method. Can be used to convert earlier winches to allow the use of the late spec UJ.Manufactured in EN24T, hardened and c..
Fairey Drum Winch Drop PTO gasket kit. Part no: FWL-221, FWL-225, FWL-242. PLEASE NOTE: This gasket kit will not for the earlier Mayflower Type PTO, which is shorter...